There are many great nail gun-like tools out there, and most of them do their work finely. The key fact is, why choose a specific one like Harbor Freight? So, I can pass through the answer like this: harbor nail guns have a suitable remark on being the 3 in 1 nailer.

Here, the final work output is pretty neat with round-headed nails, and it’s visibly apparent. Maybe that is the reasoning for it to be good despite being not cordless and heavy. I’ll be unveiling more reasons and remarks on the go.
Table of Contents
Critical Features of Harbor Freight Nailer Review
Harbor Freight tools have their dimension of fame for delivering great compatible stuff. One of the great nailers is supplied by them, and the nailers have a good review always. Each unique component of the nail guns will be made clear in the next portion.
Weight
In terms of working with a nail gun and pressurized air pops, it’s crucial to have a certain level of weight. And approximately most of the Harbor freight nailers come with 8-10-12 pounds. This is a lightweight measure but not one of the most lightweight guns.
Then again, this minimal weight gives an extra stance to work against the CFMs. We do not forget to mention the fine grip that offers an outstanding balance along with the weight. Ultimately it is not always a lightweight nailer to deal with.
Nails and All About Them
There are different angled nails in strips, and not every gun is suitable to deal with all of them. Harbor freight’s some models do have 21°, 28°, 34° facilitated nail working adjustments. Often for this variant gauge angle flexibility, it is said to cover a 3 in 1 tool.
In each magazine of the nail gun, you can more or less fill 60-100 nails. And each strip of the nails consists of 25-26 pins. More importantly, the nail they use is round-headed nails.
The magazine has a pull off-on mechanism trigger pulled in when the magazine is loaded and pulled out when it is loaded. The functionality is as easy as it’s written. When it comes to nail, they are 2-3/8”- 3¾”, and when popped, they are nicely in the logs.

Hoses and Pressures
The harbor freight framing nailers have a 360 rear hose adjustment which gives a better experience while working with the heavy models. A 20-gallon air compressor can have 95-100 psi for shooting the nails. And below an 8-gallon compressor, it will be hard to have a good outcome from the nailer.
Harbor Freight Covers 3 Angles in 1 Nailer
Generally, the magazines of a nailer are one-angled efficient, and for a different angled gauge, you might switch to another nail gun. Harbor freight has covered 21°, 28°, 34° magazine angle in the central pneumatic model. This is undoubtedly a great convention if you know how tough it is to deal with angular strips.
Harbor Freight is Not For Professionals
If you are thinking of making your treehouse or render your dog’s house, this can be a tremendous comparative tool. Also, if your job for nailing is not that vital, like remodeling the whole home, this is just not the stuff.
You see, this does have a good amount of weight and is also dependent on the hose and compressor, so it cannot be a freehand work handy. In these cases, you might go for a cordless, lighter weighted one.
Modes of Harbor Freight Nail Guns
These nail guns work on two modes, that are single shots and bump drive. The single shots work one by one and are no bound of working in a row, just up to your choice, and the bump is like a continuous shotgun.
Either way, the single shots give a better in the nails, while the bump mode has drawbacks of giving the staples an uneven push. The air pop needs to be fully covered if you want the pins to go full, and in the case of bump mode, it seems not working that way.
Also, a driving fire lockout mode enables off the fire before all nail’s runout from the magazine. Almost when 3-4 pins are left, the gun stops shooting. And the teeth like the front give extra hold, so the pops are better.
Nail Gauges for Harbor Freight
For the magazine, there are different angle customization. But in terms of working with the nail gauges, the specifications reveal that the gauge size is between 10-15. The height of the meters is a thin-like figure.
Frequently Asked Questions
Can I do heavy-duty work with Harbor freight nailers?
Even though they say this will give you the minimum fatigue but as you can see, they have a weight and the compressor hold, so this can be a little tiring for heavy-duty works.
Can I work with a 3-gallon compressor for Harbor freight nailers?
It is recommended to have over 8-gallons for the compressor. The overall tool needs some minimal requirements, and this is up to that. In that way, the air pressure will be with a good stance.
Conclusion
Like many other nailers available in the market, Harbor Freight is giving its fight to be one of the great ones. And surprisingly, it has become a favorite one. Pushing away a few odds that they have, the rubbery body better handles the users. And with a great stance comes a great outcome.
Leave a Reply